Open Access

The usage of high-level synthesis (HLS) tools for FPGAs has increased significantly over the last years since they matured and allow software programmers to take advantage of reconfigurable hardware technology. Most HLS tools employ methods to optimize for loops, e. g. by unrolling or pipelining them. But there is hardly any work on the optimization of while loops. This comes at no surprise since most while loops have loop-carried dependences involving the loop condition which result in large recurrence cycles in the dataflow graphs. Therefore typical while loops cannot be parallelized or pipelined. We propose a novel transformation which allows to optimize while loops nested within a for loop. By interchanging the two loops, it is possible to pipeline (and thereby parallelize) the inner loop, resulting in a reduced execution time. We present two case studies on different hardware platforms and show the speedup factors - compared to a host processor and to an unoptimized hardware implementation - achieved by our while loop optimization method.

This paper presents an optimized algorithm for estimating static and dynamic gait parameters. We use a marker- and contact-less motion capture system that identifies 20 joints of a person walking along a corridor. Based on the proposed gait cycle detection basic metrics as walking frequency, step/stride length, and support phases are estimated automatically. Applying a rigid body model, we are capable to calculate static and dynamic gait stability metrics. We conclude with initial results of a clinical study evaluating orthopaedic technical support.

With the increasing size and complexity of embedded systems, the impact of software on energy consumption is becoming more important. Previous research focused mainly on energy optimization at the hardware level. However, little research has been carried out regarding energy optimization at the software design level. This paper focuses on the software design level and addresses the gap between software and hardware design for embedded systems. This is achieved by proposing a framework for software design patterns, which takes aspects of power consumption and time behavior of the hardware level into account. We evaluate the expressiveness of the framework by applying it to well-known and novel design patterns. Furthermore, we introduce a dimensionless numerical efficiency factor to make possible energy savings quantifiable.

The simulation of the residual stress field achieved by shot peening cannot be carried out on component-large models. Hence, an efficient unit cell model for the simulation of the shot peening process is developed. The model allows both, the simple inclusion of a pre-stress and the evaluation of the up-arching of the Almen strip. For this purpose, generalized coupling constraints for the periodic boundaries of the unit cell are developed. These allow for displacement and rotation of the coupled boundaries relative to each other. In the coupling constraints, this is accomplished by respective variables, which can either be prescribed to the analysis or read out as a result from the analysis. Hence, the unit cell can expand, shear, bend and twist under driving forces like, e. g., residual stresses or thermal effects. At the same time, deformations of the cell’s periodic boundary pairs are kept congruent by the generalized coupling. The ability to cover expansion is novel regarding known periodic boundary conditions. Also, the application of a generalized unit cell to shot peening is new. Results obtained with the generalized unit cell are displayed, demonstrating its capabilities: A fundamental analysis of the residual stress field from shot peening shows inhomogeneities at a fatigue relevant level to be inevitable. A validation of the model was done by comparison with experimental Almen strip shot peening tests reported in literature. Shot peening under pre-stress is demonstrated and its results in terms of residual stress are evaluated. The application of the generalized unit cell is not limited to shot peening.

Es werden drei Modellierungsansätze zur Simulation von Laserscannern in Pflanzenbeständen für die Entwicklung umfeldbasierter Fahrzeugfunktionen beschrieben. Das Sensorsignal der Distanzmessung wird dabei anhand realer Messwerte oder phänomenologisch und auf der Basis empirisch ermittelter Kennwerte in Abhängigkeit von objekt- und sensorspezifischen Einflussfaktoren abgebildet. Basierend auf den Methoden zur Simulation von Distanzmesssystemen der Open Source Simulationsumgebung Gazebo wurden die Modellierungsansätze als spezifische Sensor- und Umfeldmodelle implementiert. Die Modelle wurden insbesondere für den Einsatz an mobilen landwirtschaftlichen Arbeitsmaschinen und für die Anwendung in der Getreideernte optimiert.