620 Ingenieurwissenschaften und Maschinenbau
Refine
Year of publication
Document Type
- Conference Proceeding (16)
- Article (11)
- Working Paper (5)
- Book (1)
- Master's Thesis (1)
- Moving Images (1)
Keywords
- Solarthermie (5)
- Autarkie (2)
- Container (2)
- Energie (2)
- Kugelstrahlen (2)
- Simulation (2)
- Validierung (2)
- Additives (1)
- Auftragschweißen (1)
- Chromatography (1)
Institute
Oleamide is used as a lubricant in the manufacturing and application of polypropylene (PP) medical devices. Samples of PP were prepared with 0, 1500, and 15 000 ppm oleamide content as lubricant. The samples were either left non-sterile, sterilized with ethylene oxide (ETO), γ-radiation (γ) or autoclaved (A) and stored for up to 4 weeks. To determine the oleamide bulk-to-surface distribution depending on sterilization method and storage time an extraction method and a washing technique were applied. The oleamide content was determined by gas chromatography (GC-FID) and compared with the coefficient of friction (COF). The COF dependent on the measured lubricant content at the surface. The content of lubricant on the surface depends on the type of sterilization: ETO increased the lubricant content to some extent, γ-sterilization and autoclaving reduced it. After storage, no migration of the lubricant to the surface could be detected.
The aim of this study was to provide a systematic overview of available pressure ulcer prevention quality indicators and to evaluate the underlying empirical evidence. A systematic mapping review was conducted with combined searches in Embase and Medline, and websites of relevant institutions and organisations. The eligibility criteria were clear use of the term “quality indicator” regarding pressure ulcer prevention; English or German language; and all settings, populations, and types of resources, including articles, brochures, and online material. In total, n = 146 quality indicators were identified. Most indicators were published in the United States (n = 50). The majority of indicators was developed for the hospital setting (n = 102). Process indicators were the most common (n = 71), followed by outcome indicators (n = 49). Less than half of identified indicators appeared to be practically used. Evidence supporting the validity and reliability were reported for n = 25 and n = 30 indicators respectively. The high number of indicators demonstrate the importance of measuring pressure ulcer prevention quality. This is not an indicator of our ability to accurately measure and evaluate this construct. There is an urgent need to develop evidence-based and internationally comparable indicators to help improve patient care and safety worldwide.
A systematic study was performed to understand the effects of the devulcanizing agent dibenzamido diphenyl disulfide (DBD) on the vulcanization and devulcanization process of a sulfur-cured ethylene-propylene-diene monomer (EPDM) rubber. The influence of DBD on vulcanization was investigated by mixing DBD with virgin rubber and curative system. The devulcanization of rubber waste was achieved with varying amounts of DBD ranging from 0.4 to 13.8 wt% and temperatures from 150 to 200°C. The quality of vulcanizates and devulcanizates was evaluated by rheometer tests, temperature scanning stress relaxation measurements, and analysis of mechanical properties. During vulcanization, DBD acts as an accelerator in the presence of sulfur. When accelerators are added, the scorch time increases, and the cure rate decreases. Thus, DBD acts as a retarder. In the presence of activators, DBD leads to a significant reduction of crosslink density. This results in composites with high elongation at break and poor compression set values. The efficiency of the devulcanization of rubber waste depends strongly on DBD concentration and temperature. The monosulfidic crosslinks are cleaved by low concentrations of DBD, while polysulfidic crosslinks require higher concentrations. These results show that DBD is effective as a devulcanizing agent and degrades the network below 200°C.
Vanadium carbide (VC) reinforced FeCrVC hardfacings have become important to improving the lifetime of tools suffering abrasive and impressive loads. This is because the microstructural properties of such hardfacings enable the primary VCs to act as obstacles against the penetrating abrasive. Because dilution is supposed to be the key issue influencing the precipitation behaviour of primary carbides during surfacing, the development of deposit welding processes exhibiting a reduced thermal impact, and hence lower dilution to the base material, is the primary focus of the current research. By inserting an additional hot wire in the melt, an approach was developed to separate the material and energy input during gas metal arc welding (GMAW) and hence realised low dilution claddings. The carbide content could be increased, and a grain refinement was observed compared with conventional GMAW. These effects could be attributed to both the reduced dilution and heterogeneous nucleation.
Innerhalb eines Forschungsprojektes wurde ein Energiesystemoptimierungsmodell entwickelt, das mögliche Geschäftsmodelle als Weiterbetriebsoptionen für Biogasanlagen betrachtet. Insbesondere der Einfluss von fluktuierenden Strommarktpreisen und variierenden Treibhausgasquoten soll kritisch im innerdeutschen Kontext beleuchtet werden.
Der nachfolgende Projektbericht, welcher im Rahmen des Masterprojektes und des Moduls „Bildgebende Sensortechnik“ erarbeitet wurde, ist wie folgt den beiden Fächern zuzuordnen.
Die Kapitel, welche sich mit der Inbetriebnahme und den Umgang des SICK RMS320 Radarsensors beschäftigen, sind Teil des Masterprojektes. Dies betrifft die Kapitel 2.2, 4.1, 4.3 und in Teilen das Kapitel 4.5.
Dem Modul „Bildgebende Sensortechnik“ sind hingegen die Messung des Einflusses von Kleidung auf die Erkennungsfähigkeit eines Menschen sowie die Radarmessungen der verschiedene Prüfkörper zuzuordnen. Dies wird in den Kapiteln 2.3, 3, 4.2, 4.4 und 4.5 behandelt.
Die „Grundlagen der Radartechnik“ sind für beide Teile gleichbedeutend wichtig.
A recently published study of high temperature nitridation of iron chromium aluminum alloys (FeCrAl) at 900°C in N2–H2 has redundantly shown the formation of locally confined corrosion pockets reaching several microns into the alloy. These nitrided pockets form underneath chromia islands laterally surrounded by the otherwise protective alumina scale. Chromia renders a nitrogen‐permeable defect under the given conditions and the presence of aluminum in the alloy. In light of these findings on FeCrAl, a focused ion beam–scanning electron microscope tomography study has been undertaken on an equally nitrided FeNiCrAl sample to characterize its nitridation corrosion features chemically and morphologically. The alloy is strengthened by a high number of chromium carbide precipitates, which are also preferential chromia formation sites. Besides the confirmation of the complete encapsulation of the corrosion pocket from the alloy by a closed and dense aluminum nitride rim, very large voids have been found in the said pockets. Furthermore, metallic particles comprising nickel and iron are deposited on top of the outer oxide scale above such void regions.
Film- und Alltagsszenen als Lernfeld für die mathematisch-technische Modellbildung und Simulation
(2016)
Es werden ausgewählte Beispiele und Ideen vorgestellt, die Studierende des Moduls "Modellierung und Simulation" besonders motivieren sollen, mathematisch-technische Problemstellungen wissen-schaftlich zu bearbeiten. Dabei werden Fragestellungen aus dem persönlichen Alltag, aber auch aus dem Alltag berühmter Geheimagenten behandelt. Zu diesen Projekten gehören die Erstellung geeigneter mathematischer Modelle, die Implementierung in Matlab/Simulink® sowie die Systemsimulation. Die Erfahrungen zu Motivation und Erfolg, aber auch zu Schwierigkeiten bei der Bearbeitung werden abschließend reflektiert.
Die Kostenreduzierung solarthermischer Systeme bleibt eine der großen Herausforderungen, um die Solarthermie wirtschaftlich attraktiv zu machen. In der vorliegenden Arbeit wurde eine vollständige Simulationsumgebung geschaffen, mit der bereits in der Entwicklungsphase automatisierte Optimierungen in Bezug auf Ertrag und Wirtschaftlichkeit von Kollektoren und Systemen zur Brauchwassererwärmung und Heizungsunterstützung möglich sind. Die Anwendung dieses Simulationstools ist sowohl für den Komponentenhersteller als auch für den Systemplaner relevant.